Improve Your Workspace with a Potting Bench Gardening | 23 November 2016 Share article facebook twitter google pinterest Today we’re focusing on the center of a Venn Diagram that combines DIY projects, gardening, and outdoor living. We’re sharing step-by-step instructions for building your own garden bench from Black & Decker’s Complete Outdoor Builder, because sometimes, no matter what your project is, all you really want from your work area is a big, broad surface with plenty of room to spread out and make things. This workhorse of a bench is modeled after the most-used workspace in any home: the kitchen countertop. At 36 inches tall, the bench is the same height as most kitchen counters, and at 28 inches wide, it’s slightly deeper than standard countertops—but not so deep that you can’t easily reach across to the other side. The symmetrical configuration allows you to push any part of the bench against a wall or leave it out in the open for easy access to all sides. There’s also no need to worry about leaving the bench out in the rain. The understructure is made with moisture-resistant, pressure-treated lumber, and the top is made up of composite decking boards that won’t split, rot, or splinter and require no protective finish. Of course, if you’ve always wished your kitchen counters were a bit higher or lower, you can simply add or subtract a few inches from the given dimension for the bench legs. You can also change the length of the bench to fit a tight space, if necessary. Shortening the whole thing by two feet allows you to build it with standard 8-foot lumber and decking instead of 12-foot and 10-foot pieces. This potting bench has a 28 × 71″ top and is built with four 2 × 4s and three standard-size decking boards. The handy pot shelf below the bench top is made with a cutoff from one of the deck boards. Tools & Materials You’ll Need Tape measure Circular saw Drill Piloting-countersink bit Framing square Clamps (3) 12-ft. pressure-treated 2 × 4 3½” and 2½” deck screws (1) 10-ft. pressure-treated 2 × 4 (3) 12-ft. 1 × 6 composite decking boards Sandpaper Eye and ear protection Work gloves How to Build a Potting Bench 1 Cut the two top frame sides from one 12-ft. 2 × 4, using a circular saw or power miter saw. Cut the two top frame ends and the four top supports from another 12-ft. 2 × 4. Fit the side pieces over the ends of the end pieces so all top edges are flush. Drill countersunk pilot holes and fasten the pieces together with two 3½” deck screws at each joint. 2 Mark the layout for the top supports: Measuring from one end of the top frame, mark both frame sides every 13?”. Check the top frame for square, using a framing square. Install the top supports between the frame sides with 3½” deck screws driven through the frame sides and into the supports. Make sure the supports and frame sides are flush across the top. 3 Cut the four legs from one 12-ft. 2 × 4. Round-over the edges on the bottom end of each leg, using sandpaper, a file, or a router and roundover bit; this prevents splintering if the table is slid around. Install the legs at the inside corners of the top frame, driving 2½” deck screws through the legs and into the top frame ends. Also screw through the top frame sides and into the legs. Make sure the legs are square to the frame before fastening. 4 Mark the inside edge of each leg, 10″ up from its bottom end. Measure the distance between each leg pair and cut a leg support to fit snugly between the legs, using the 10-ft. 2 × 4. Install the leg supports with their bottom edges on the marks; drive 3½” screws toenail style through the top and bottom edges of the supports and into the legs. 5 Cut the 2 × 4 stretcher to fit snugly between the leg supports, using the remainder of the 10-ft. 2 × 4. Install the stretcher so it’s centered side-to-side on each support, with the top edges flush. Drive 3½” screws through the outsides of the leg supports and into the stretcher ends. 6 Cut the top decking boards to length. Clamp the first board in place so it overhangs the front and ends of the top frame by ¾”. If the deck boards are crowned (slightly curved across the face), make sure the convex side faces up. Drill two pilot holes at the center of each top frame end and top support location, countersinking the holes slightly. Fasten the board with 2½” deck screws. 7 Install the remaining deck boards so all of their ends are perfectly aligned and each board is gapped ?” from the next (without gaps, the joints would trap dirt). Use pieces of 1?8″-thick hardboard or two ?”-dia. drill bits to set the gaps. The last board should overhang the rear frame side by ¾”. 8 Complete the pot shelf by cutting the remaining half piece of deck board to length. Position the board so it is centered side-to-side over the stretcher and overhangs both leg supports by ¾”. Fasten the board to the stretcher and leg supports with 2½” deck screws driven through pilot holes. Buy from an Online Retailer US: UK: Find more than 150 projects for building custom decks, patios, fences, sheds, and more! From building a new deck to creating a garden pathway, the great outdoors is the most popular place for homeowners to showcase their creativity and skill. With more than 150 outdoor building projects shown with step-by-step photography, Complete Outdoor Builder has a project for anyone, guaranteed to improve your yard. This updated and redesigned book with a handsome hardcover is sure to find a permanent place on the shelf of anyone who wants to create and maintain a beautiful outdoor living space. Some of the projects covered in Complete Outdoor Builder include: – Attached deck – Fences – Composite railings – Sheds – Walkways – Playset – Treehouse – Landscape steps – Arbor – . . . and much more! The Complete Outdoor Builder includes a wide range of projects and appeals to all skill levels. Building decks and patios are among the most popular categories for outdoor construction, and you’ll find all the techniques and skills–as well as complete lists of tools and materials required–to design and build your own. Complete Outdoor Builder also offers plans and revamped photography for more than a dozen designs that you can replicate or use as inspiration for a custom project. Designed, built, and photographed by professionals, the fun projects in this book also have the stamp of approval from Black & Decker, the most trusted name in DIY tools and equipment. Roll up your sleeves; it’s time to build something great. The editors and publishers at Cool Springs Press have combined their decades of experience to create more than 30 best-selling classics on gardening, landscaping, home repair, and remodeling. With the added expertise of the United States’ most knowledgeable Do It Yourself writers and photographers, our state and local gardening books are tailored to specific regional environments across the country, while our renowned series of foolproof home improvement books have long been trusted on both the bookshelf and the job site. View our full catalog at CoolSpringsPress.com or connect with us on: Facebook (facebook.com/QuartoHomes) Twitter (@quartohomes) Pinterest (pinterest.com/QuartoHomes). Share article facebook twitter google pinterest If you have any comments on this article please contact us or get in touch via social media.